Taping and jointing compounds are designed to reinforce plasterboard joints and make them invisible. They do two jobs: bedding the tape, then filling and finishing the joint, to leave a perfectly flat surface ready for paint or wall coverings. Formulated for strong adhesion, a smooth glide and easy sanding, they limit shrinkage as they dry and prevent hairline cracking.
They come either as a powder, mixed with water on site, for a controlled set, or ready mixed, for a consistent texture and time saved. Both meet the demands of drylining professionals on new build and renovation work alike. On this page, PRESTONETT MULTIPURPOSE FILLER is the powder, mixed at 0.5 litres of water per kg; BAGAR AIRLISS J, BAGAR AIRLISS J LIGHT and PRESTONETT MULTI-LIGHT FILLER are ready mixed.
Our taping and jointing compounds
What is a taping and jointing compound?
A jointing compound is a fine, cohesive material, formulated to soak into paper or reinforced tape and hold it in place without blistering. It has to stay workable long enough for wet-on-wet work, while hardening evenly to take the following coats. Bedding and filling compounds handle the first coat and fill the recess; finishing compounds true up the joint and feather out the build-up along its edges. BAGAR AIRLISS J and BAGAR AIRLISS J LIGHT are designed for all stages of plasterboard jointing and finishing, and for fixing corner tapes and beads.
Some compounds can also be applied mechanically, as well as by hand with a filling knife or blade. BAGAR AIRLISS J and BAGAR AIRLISS J LIGHT can be applied with a banjo and are suitable for use with all automated taping and jointing tools, such as the bazooka, Mudshot and flat boxes. They can also be sprayed with an airless machine, with a tip size of up to 3.33 for joint filling. PRESTONETT MULTI-LIGHT FILLER is applied by hand or with a dedicated roller, PRESTONETT MULTIPURPOSE FILLER by hand. This versatility lets you match the tool and the pace to the size of the job, with no compromise on the final finish.
When to use a jointing compound, and how to choose one
Use a jointing compound at every board joint: tapered-edge joints, butt joints, internal angles and external corners. The choice depends on the job: time before handover, humidity on site, application method and the level of finish required. None of the four compounds on this page should be applied below 8°C or above 35°C, or at a relative humidity above 70%.
On fast-moving jobs, a ready mixed compound suited to mechanical application, such as BAGAR AIRLISS J or BAGAR AIRLISS J LIGHT, gives high output and consistency. For precise control over setting time, a powder is the right choice: PRESTONETT MULTIPURPOSE FILLER has a working time of approximately 60 minutes at 20°C. Also check compatibility with your tapes (micro-perforated paper tape, reinforced corner tape), ease of sanding and filling power.
All four compounds are classified as jointing materials for gypsum plasterboards to EN 13963: type 3A for BAGAR AIRLISS J, BAGAR AIRLISS J LIGHT and PRESTONETT MULTI-LIGHT FILLER, and type 4B for PRESTONETT MULTIPURPOSE FILLER.
The work is done in three stages: bed the tape, pressing it firmly into place and squeezing out the surplus; apply a filling coat to bury the tape; then lay on a wide finishing coat to feather the joint into the face of the board. For BAGAR AIRLISS J, the data sheet specifies a finishing coat taken 5 cm beyond the taper on either side. Allow each coat to dry and dust off between coats, then, where necessary, finish with a suitable primer before painting.
Benefits for a lasting result
Well chosen and correctly applied, a jointing compound ensures a seamless surface, long-term stability and the best possible base for decorative finishes. Modern formulations are comfortable to apply, glide consistently and sand evenly, for a clean result with no visible build-up. With mechanical application, you gain productivity and consistency while keeping consumption under control. As a guide, the data sheets give an average consumption for taping of 0.45 kg per linear metre for BAGAR AIRLISS J and 0.35 kg per linear metre for BAGAR AIRLISS J LIGHT.



