Exterior walls take the full force of the weather. Rain, swings in temperature and pollution put façades under stress, and cracks and irregularities follow. An exterior filler corrects these defects, evens out the substrate and gives paint or a decorative coating a sound base to bond to.
Unlike a decorative finish, it is a technical coat: it prepares the substrate and helps the whole system last. Choosing a filler suited to exterior conditions and to the type of substrate is therefore essential for a quality refurbishment.
Our exterior plasters and fillers
What is an exterior filler, and when should you use one?
Quick-drying fillers for holes and cracks
An exterior filler is formulated to withstand the weather while remaining permeable to water vapour. PRESTONETT EXTERIOR QUICK DRY FILLER, for example, is a fibre-enriched powder that fills holes and cracks up to 4 cm deep. It mixes without lumps and bonds strongly to a wide range of substrates: concrete, cellular concrete, cement, concrete block, brick, stone, plaster, mortars and old painted substrates.
Once mixed, it can be worked for about 35 minutes and overcoated after about 3 hours (at 20°C and 55% RH, for a 4 cm repair), so you can apply, sand and paint on the same day. This quick turnaround is a real help when cracks need repairing quickly before painting.
Masonry repairs and levelling
For broader work on masonry, PRESTONETT WATERPROOF MASONRY FILLER is designed for waterproofing, filling and finishing masonry substrates, and for repairing and shaping window sills and mouldings. This grey powder fills up to 15 mm in one application on concrete, cellular concrete, cement, concrete block, brick, stone and mortars, and is waterproof from 3 mm thick. It is also used to repair reinforced concrete, providing protection against carbonation, and it resists saltpetre and seawater.
For levelling over larger areas, there is BAGAR AIRLISS EXT, a ready mixed spray-applied leveller for exterior use. It is applied up to 5 mm thick, by hand or with an airless or spray machine, on concrete, cement, concrete block, brick and old painted substrates. It is suitable for levelling contraction and control joints in concrete and for finishing the undersides of balcony slabs before decoration. Both products are water vapour permeable, so the wall can breathe, and BAGAR AIRLISS EXT is also water and humidity resistant.
Interior and exterior fillers for walls and woodwork
Alongside these, seven Prestonett fillers for both interior and exterior use cover repairs on walls and woodwork:
- PRESTONETT READY MIXED FILLER: fills small holes and cracks up to 1 cm. Dries hard, is easy to sand, will not flash or grin and needs no spot priming.
- PRESTONETT LIGHT WEIGHT FILLER: a lightweight filler for holes and cracks of all sizes, applied at any thickness. It fills and finishes in a single pass and does not shrink or crack.
- PRESTONETT QUICK DRY FILLER: for minor surface repairs up to 3 mm, ready to sand and paint in 15 minutes. Water and humidity resistant, in a 200 ml tube.
- PRESTONETT FLEXIBLE CRACK REPAIR FILLER: for recurring cracks caused by structural movement. Highly flexible, fibre reinforced and waterproof, it is applied up to 3 mm thick and needs no fibre tape or fabric.
- PRESTONETT WOODFILLER (TUBE): for holes and cracks in doors, window frames, skirting boards and floorboards, up to 5 mm. Outdoors, it must be overcoated with a weatherproof stain, varnish or paint, and it must not be applied to damp wood.
- PRESTONETT WOOD FILLER: fills and skims most types of wood, including chipboard, plywood and exotic timbers, up to 1 cm.
- PRESTONETT WOOD REPAIR: a powder for filling holes and cracks in all types of woodwork and rebuilding wood lost to decay, at any thickness. Very hard when dry, it can be carved, drilled and painted. Working time about 30 minutes.
How to prepare and apply an exterior filler
Preparing the substrate determines how long the repair will last. Remove any old coating or primer that is not firmly bonded: the closer you get to a sound, bare substrate, the better the filler will bond. Substrates must be hard, cohesive, clean, sound and dry. With PRESTONETT EXTERIOR QUICK DRY FILLER, powdery or soft primers must be hardened first and any metal reinforcement treated beforehand with a suitable product. After cleaning, a simple absorbency test shows how porous the surface is: if water soaks in, apply a suitable primer to secure the bond; if it beads on the surface, a light sanding is needed.
Powder fillers are mixed with the stated amount of water to give a smooth, even paste, pouring the powder gradually into the water: 0.45 L per kg for PRESTONETT EXTERIOR QUICK DRY FILLER, 0.25 L per kg for PRESTONETT WATERPROOF MASONRY FILLER and 0.50 L per kg for PRESTONETT WOOD REPAIR. Ready mixed products need no mixing water: BAGAR AIRLISS EXT is stirred before use and can be thinned with up to 3% water if necessary, and the tubes of PRESTONETT QUICK DRY FILLER and PRESTONETT WOODFILLER (TUBE) are kneaded before application.
All the products on this page can be applied by hand, with a filling knife, blade or smoothing trowel depending on the product. On larger areas, BAGAR AIRLISS EXT can also be sprayed with an airless machine or a spray machine.
Apply an even coat at the right thickness for the product: up to 5 mm for BAGAR AIRLISS EXT, up to 15 mm in one application for PRESTONETT WATERPROOF MASONRY FILLER, and from 2 mm up to 4 cm for PRESTONETT EXTERIOR QUICK DRY FILLER. Smooth out any lap marks and leave to dry before finishing: PRESTONETT WATERPROOF MASONRY FILLER, for example, is overcoated after 48 hours. A light sanding removes any build-up before the exterior paint goes on. All the products on this page are applied between 5°C and 35°C, at a relative humidity no higher than 80%, and PRESTONETT EXTERIOR QUICK DRY FILLER must not be applied in direct sunlight.
Benefits and tips for façades and exterior walls
Lasting protection that lets the wall breathe
A quality exterior filler protects the façade from the weather while letting moisture from inside the wall escape. Microporous formulations help prevent blistering and flaking, even where humidity varies widely: PRESTONETT EXTERIOR QUICK DRY FILLER, PRESTONETT WATERPROOF MASONRY FILLER and BAGAR AIRLISS EXT are all water vapour permeable. Fibres add mechanical strength, so fibre-enriched PRESTONETT EXTERIOR QUICK DRY FILLER fills cavities without shrinking or cracking. BAGAR AIRLISS EXT and PRESTONETT EXTERIOR QUICK DRY FILLER both bond strongly and can be sanded, leaving a flat surface ready for exterior paint or a waterproofing coating, the overcoats specified on their data sheets.
Products for every stage of the job
Beissier’s exterior ranges cover each stage of a refurbishment: quick filling with PRESTONETT EXTERIOR QUICK DRY FILLER, masonry repairs with PRESTONETT WATERPROOF MASONRY FILLER and spray-applied levelling with BAGAR AIRLISS EXT. Most of the products on this page offer excellent adhesion to a wide range of substrates, and their working times suit the pace of the job: about 35 minutes for PRESTONETT EXTERIOR QUICK DRY FILLER, about 30 minutes for PRESTONETT WATERPROOF MASONRY FILLER and PRESTONETT WOOD REPAIR, and unlimited for the ready mixed Prestonett fillers. On the environmental side, VOC content goes as low as 0.5 g/L (EU limit value: 30 g/L), up to 83% of the raw materials are of natural origin, depending on the product, and the three powder fillers come in 100% recyclable packaging.
Choose the right filler for the job and follow the application guidelines, and your façades and exterior walls will have a finish that looks good and lasts.









